*save_as_model C:\Users\manto\Documents\201819_esami\PAOM\20190328_PAOM_lab\torsione_rev01_labile.mud yes
|===================================
|		MESH GENERATION: START
|===================================
|===================================
|		ADD NODES
|===================================
*add_nodes
0 0 0
19 0.05 0
19 59 0
-19 59 0
-19 0 0
*reset_view
*fill_view
|===================================
|		ADD CURVES
|===================================
*set_curve_type line
*add_curves
 point( 1.900000000000e+001, 5.000000000000e-002, 0.000000000000e+000)
 point( 1.900000000000e+001, 5.900000000000e+001, 0.000000000000e+000)
 2
 point(-1.900000000000e+001, 5.900000000000e+001, 0.000000000000e+000)
 3
 point(-1.900000000000e+001, 0.000000000000e+000, 0.000000000000e+000)
*reset_view
*fill_view
|===================================
|	NODES AND CURVES LABELLING
|===================================
*set_node_labels on
*regenerate
*set_curve_direction on
*set_curve_labels on
*regenerate
|===================================
|		CURVE DIVISION
|===================================
*set_curve_div_type_fix_avgl
*set_curve_div_avgl 20
*apply_curve_divisions
all_existing
|===================================
|	FROM CURVES TO 1D ELEMENTS
|===================================
*mesh_curves
all_existing
|===================================
|	FROM 1D ELEMENTS TO SHELL
|===================================
*expand_reset
*set_expand_repetitions 2
*set_expand_translation z 20
*expand_remove
*expand_elements
all_existing
*expand_reset
|===================================
|	SYMMETRY PLANE XZ, NORMAL Y
|===================================
*symmetry_reset
*set_symmetry_point
0 0 0 
*set_symmetry_normal
0 1 0
*symmetry_elements
all_existing
*symmetry_reset
|===================================
|	SWEEP NODES
|===================================
*set_sweep_tolerance
0.0001
*sweep_nodes
all_existing
|===================================
|	HIDE LABELLING NODES AND CURVES
|===================================
*set_node_labels off
*regenerate
*set_curve_direction off
*set_curve_labels off
*regenerate
|===================================
|		MESH GENERATION: FINISH
|===================================
|===================================
|		GEOMETRIC PROPERTIES: START
|===================================
|===================================
|	APPLY SHELL THICKNESS PROPERTIES
|===================================
*new_geometry 
*geometry_type mech_three_shell
*geometry_name thickness_2mm
*geometry_param thick
2
*add_geometry_elements
all_existing
|===================================
|	ID GEOMETRY 
|===================================
*identify_geometries 
*regen
|===================================
|	PLOT 3D EXPAND AND OFFSET
|===================================
*draw_shells_expanded on
*draw_offsets on
*elements_solid
*regenerate
|===================================
|	SET OFFSET (FOR COMPLETENESS)
|  NO APPLIED FOR THE PRESENT MODEL
|===================================
|*geometry_option offsets:on
|*geometry_param offset
|*geometry_param offset -1
|*regenerate
|===================================
|	CHECK BOTTOM AND TOP SHELL
|===================================
*identify_backfaces *regen
*regenerate
|===================================
|	CHECK ELEMENTS
|	FLIP BOTTOM AND TOP SHELL
|===================================
*flip_elements
all_existing
|===================================
|	PLOT ELEMENTS 
|   no expand no offset
|===================================
*identify_none *regen
*draw_shells_expanded off
*draw_offsets off
*regenerate
|===================================
|		GEOMETRIC PROPERTIES: FINISH
|===================================
|===================================
|		MATERIAL: START
|===================================
|	ISOTROPIC ELASTO-PLASTIC
|===================================
*new_mater standard 
*mater_option general:state:solid
*mater_name 
*mater_name alluminio
*mater_param general:mass_density 2.7e-9
*mater_param structural:youngs_modulus 70000
*mater_param structural:poissons_ratio 0.3
*add_mater_elements
all_existing
*identify_materials *regen
*identify_none *regen
|===================================
|	ORTHOTROPIC ELASTO-PLASTIC (FOR COMPLETENESS)
|  NO APPLIED FOR THE PRESENT MODEL
|===================================
|*new_mater standard 
|*mater_option general:state:solid
|*mater_name aluminium_ortho
|*mater_option structural:type:elast_plast_ortho
|*mater_param general:mass_density 2.7e-9
|===================================
|	Show elements by wireframe
|===================================
*elements_wireframe
*regenerate
|===================================
|		MATERIAL: ORIENTATION
|===================================
*new_orient 
*orient_type uu_plane
*set_orient_vector1
0 
0
1
*set_orient_vector2
1
1
0
*add_orient_elements
all_existing
|===================================
|	PLOT THE ORIENTATION
|   PREFERRED SYSTEM
|===================================
*set_orient_custom on
*regenerate
*set_orient_custom off
|===================================
| Deflag the orientation plot
|===================================
*set_orients off
*regenerate
|===================================
|		MATERIAL: FINISH
|===================================
|===================================
|		LINK: START
|===================================
|===================================
| Definition
| of the retained node
|===================================
*add_nodes
0
0
40
*reset_view
*fill_view
|===================================
| Store
| of the retained node
|===================================
*select_clear_nodes
*select_method_single
*select_mode_and
*select_nodes
104
# | End of List
*store_nodes retained_node_z40
all_selected
*reset_view
*fill_view
|===================================
| Definition  
| of the tied nodes
| the retained node cannot be included 
| into the tied nodes. 
| EXIT NUMBER 2011
|===================================
*select_clear_nodes
*select_method_box
*select_mode_and
*select_nodes
-1000
1000
-1000
1000
39.9
40.1
*select_method_single
*select_mode_except
*select_nodes
retained_node_z40
|===================================
| Store 
| of the tied nodes
|===================================
*store_nodes tied_nodes_z40
all_selected
*select_clear_nodes
|===================================
| RBE2
|===================================
|	FREE WARPING
|   z-displacement free
|   rotation along x and y axis are free
|===================================
*new_rbe2
*rbe2_ret_node
104
*rbe2_tied_dof 1
*rbe2_tied_dof 2
*rbe2_tied_dof 6
*add_rbe2_tied_nodes
tied_nodes_z40
|===================================
|		LINK: FINISH
|===================================
|===================================
|		BCS: START
|===================================
|===================================
| Definition  
| of the fixed nodes
| the O(0,0,0) node 
| has been omitted from the BCs 
|===================================
*select_clear_nodes
*select_method_box
*select_mode_and
*select_nodes
-1000
1000
-1000
1000
-0.01
0.01
*select_method_single
*select_mode_except
*select_nodes
 1
# | End of List
|===================================
| Store 
| of fixed nodes
|===================================
*store_nodes skew_symm_nodes_xy
all_selected
*select_clear_nodes
|===================================
| Skew-symmetry xy at midplane
|===================================
*new_apply 
*apply_type fixed_displacement
*apply_name skew_symm_xy
*apply_dof x *apply_dof_value x
*apply_dof y *apply_dof_value y
*apply_dof rz *apply_dof_value rz
*add_apply_nodes
skew_symm_nodes_xy
|===================================
| Rotation Z imposed at the free 
| profile section at the retained
| node of the RBE2
|===================================
*new_apply *apply_type fixed_displacement
*apply_name rotation_z
*new_md_table 1 1
*set_md_table_method_formula
*md_table_formula v1
*set_md_table_type 1
z0_coordinate
*apply_dof x *apply_dof_value x
*apply_dof y *apply_dof_value y
*apply_dof z *apply_dof_value z
*apply_dof ry *apply_dof_value ry
*apply_dof rx *apply_dof_value rx
*apply_dof_value rz 0.001
*apply_dof_table rz
table1
*add_apply_nodes
104
# | End of List
|===================================
|		BCS: FINISH
|===================================
|===================================
|		JOBS: START
|===================================
*prog_use_current_job on 
*new_job 
*job_class structural
|===================================
|		OUTPUTS REQUEST
|===================================
|	AVAILABLE ELEMENT TENSOR
|	AVAILABLE ELEMENT SCALAR
|===================================
*add_post_tensor stress_p
*post_eq_outer_layers stress_p
*add_post_var von_mises
*post_eq_max_min_layers von_mises
*add_post_var elem_orient_1
*add_post_var elem_orient_2
|===================================
|	AVAILABLE NODAL QUANTITIES
|===================================
*job_option nod_quantities:manual
*add_post_nodal_quantity Displacement
*add_post_nodal_quantity Rotation
*add_post_nodal_quantity Rea_Force
*add_post_nodal_quantity Rea_Moment
*add_post_nodal_quantity Ty_Force
*add_post_nodal_quantity Ty_Moment
|===================================
|  ELEMENTS ASSIGNMENT FORMULATION
|===================================
*element_type 75
all_existing
|===================================
|  SAVE AND CHECK
|  WARNING AND ERRORS at prompt
|===================================
*save_model
*check_job
*update_job
*submit_job 1 
*monitor_job
|===================================
|		JOBS: FINISH
|===================================
|===================================
|		JOB RUN DEBUG
|===================================
| The EXIT NUMBER is 3004 
| open the file .log
|===================================
|===================================
|		OPEN RESULTS 
|===================================
*open_post default
*post_numerics
*post_value Displacement Z
*post_close
|===================================
|		SAVE A NEW FILE 
|===================================
*save_as_model C:\Users\manto\Documents\201819_esami\PAOM\20190328_PAOM_lab\torsione_rev01_nolabile.mud yes
|===================================
|		BCs UPDATED
|===================================
*new_apply 
*apply_type fixed_displacement
*apply_name positioning_z
*apply_dof z *apply_dof_value z
*add_apply_nodes
5
# | End of List
|===================================
|	JOB UPDATED INITIAL CONDITIONS
|===================================
*add_job_applys positioning_z
|===================================
|  SAVE AND CHECK
|  WARNING AND ERRORS at prompt
|===================================
*save_model
*check_job
*update_job
*submit_job 1 
*monitor_job
|===================================
|		OPEN RESULTS 
|===================================
*open_post default
*post_numerics
*post_value Displacement Z
*post_close
|===================================